Bite wounds and puncture wounds are common sites of infection, which often leads to abscesses in dogs, cats and other pets. Understanding how to properly clean a pet's bite or puncture wound immediately following the injury will maximize a pet's chances of a quick recovery.
Cleaning a pet's wound at home immediately following the injury can help lessen the chance of infection. Even if the dog, cat or other pet will soon be brought to the veterinarian, proper bite wound care and prompt cleaning immediately after the puncture or bite will greatly increase the chances of avoiding infection.
Treating a Dog's or Cat's Bite Wound at Home
Dr. Michael Levine, DVM, offered the following tips for treating bite wounds in cats, dogs and other pets at home:
Bleeding and Bite Wounds - The wound should be allowed to bleed for a period of time following the time of injury, providing this bleeding is not copious and life-threatening in nature (in these cases, apply pressure to the wound to stem the flow.) The blood serves to flush bacteria from the wound. This is a good time to search for other injuries, as multiple bite wounds are often present.Trimming Hair from Around Bite Wounds - Once bleeding ceases, the wound will require immediate attention. Begin by trimming and shaving hair around the affected area to provide for good visibility and sufficient air flow.Washing Bite Wounds - The wound should be cleaned as soon as possible following the time of injury. Use an antibacterial soap, like Dial, to wash the wound site for two full minutes. If there are multiple wounds, each should be washed individually for two full minutes.Flushing the Wound -After washing the wound site, the area must be flushed to help rinse away bacteria and soap. This is perhaps one of the most vital steps of bite wound care, so its essential that each wound is flushed for three full minutes. The wound should be positioned directly beneath the flow of water and the water should flow inside and over the wound.How to Clean and Disinfect a Pet's Bite Wound
Once the animal is removed from the sink or tub and dried off, the second stage of bite wound treatment can begin. During this time, its vital to avoid direct contact with the pet's bite wound, as this is the stage when the wound is disinfected.
Flushing a Bite Wound (With Saline):If wound wash saline is available, (this can be found at many drug stores, usually in the first aid section near the hydrogen peroxide and other disinfectants) flush the wound for a second time with this sterile solution.Disinfecting a Bite Wound: Disinfecting the wound is an important step, so its vital to use the proper tools. Betadine iodine - a hospital-grade antiseptic that kills bacteria and disinfects the wound is preferred. Its typically available in the first aid section of the drug store and its by far the most effective antiseptic, and its well tolerated since it does not cause stinging or burning. If betadine is not available, opt for hydrogen peroxide, applied full strength. The betadine (or other antiseptic like Hydrogen Peroxide) should be poured directly onto the bite wound and allowed to flow into the wound. Use caution not to directly touch the wound after the antiseptic is applied. Wipe up any drips, but allow the area around the wound (at minimum, a hairless one-inch diameter) to air dry.Dressing a Bite Wound: Dressings are not ideal for bite wounds, as this limits air flow to the site. But immediately following the injury, the animal caretaker may not have the proper equipment on hand, such as an Elizabethan collar (also called an e-collar or lampshade collar) in the case of cats and dogs, therefore the injured animal may have access to lick and contaminate the wound. If this is the case, the entire flushing and disinfecting process must be repeated. So until the animal can make it to the veterinarians office (ideally, within two to twelve hours), a light dressing can be applied.Apply a dab of antibiotic ointment to the bite wound to help prevent infection in the bite wound. Then, use a gauze pad or rolled gauze to lightly cover the wound to help prevent contamination. Two layers of gauze are sufficient to protect the wound from debris and other contamination, while also still allowing for air flow to the region.
Notably, a cat's or dog's bite wound should be left uncovered for the majority of the healing process. A light dressing should only be applied for a short period of time, to protect the area until the animal can be brought to the veterinarians office.
"Antibiotics are almost always necessary for bite wounds, so bringing your pet to the vet sooner rather than later is ideal. This will help lessen pain, healing time and cost. You're going to pay a lot more later on if we need to go in and surgically debride the wound," Dr. Levine explained.
Related Articles on Caring for Pets' Wounds
Readers may also enjoy General Bite Wound Care along with Infections in Animals.
Today I will be telling you how to fix many of the problems that you might be having with your RV water pump. Few people actually understand how the water system works in their RV. If you have a 5th wheel, motor home, camper, or tent trailer, they are all basically the same so you've come to the right place to learn about them.
Chances are that if you found your way here, you are having problems with your RV water pump. Fear not. The system is relatively simple and easy to repair. The RV water system consists of a fresh water holding system, plastic or copper water pipes, a 12 volt RV water pump, a gray water tank, and a valve for dumping.
We're only going to cover the RV water pump in this article. RV water pumps are relatively simple devices. The most common manufacturer these pumps is ShurFlo. These pumps are nearly always powered by 12 volt DC electricity. Even if you are plugged into a 120 volt AC power at a RV campground, they still use 12 volt power. This is accomplished by the 120 volt AC power being directed into a power converter than changes the 120 VAC into 12 VDC electricity.
The RV water pump is an on demand system. This means that the pump only kicks on when it's needed. They work by pressurizing your water pipes to a preset PSI (pounds per square inch). This is usually about 30 PSI but most pumps are adjustable. When the power is switched on to the pump, it starts pumping. If any faucets are open, the pump continues to run providing the necessary flow of water. When you shut the faucet off, the pump continues to run until the preset water pressure is built up in the plumbing lines. When this pressure is reached, the pump automatically turns off. These pressure in the line is maintained until you open a faucet again. When you open the faucet, the pump senses a drop in pressure and begins pumping again.
Some older RV water pumps work differently. You have to manually turn the pump on when you want water. You open the faucet, turn the pump on and water flows out of the faucet. When you want to turn the water off, you turn the switch off to the pump and then close the faucet. It's important to do things in this order. These older pumps don't shut off when the water reaches a preset pressure in the line. Leaving the pump running will either overheat the pump or burst a plumbing line.
RV Water Pump Troubleshooting
Like any system in an RV, there are things that can sometimes go wrong. Below are the procedures for troubleshooting your RV water pump.
Is there water in the holding tank. Believe it or not this is often overlooked. It's possible for the water gauges to accumulate residue on them and read full when they are in fact empty.Make sure there is power to the pump. Is your RV battery fully charged? If not, you can plug into 120 volt power to make sure you have power to the pump. There is usually a fuse in the positive wire somewhere near the pump. Check the fuse to see if it is blown. If it's blown, replace it and your problem is usually solved. Check to see if the connections to the pump are good. Since RV's usually travel the road, it's possible for these connectors to come loose. If the fuse is good, use a 12 volt test light or better yet a multi-meter to check for power at the pump. If you don't have power, check the connections at the battery and the power converter. If they are bad, repair them and your problem should go away. If they are good, you want to inspect the wiring for breaks or shorts. If there are bad spots in the wiring, you will need to repair or replace the wiring. Another thing that can fail is the switch to the pump. The easiest way to test this is to bypass the switch and connect the RV water pump directly to the positive and negative wires. If you do this and the pump functions normally, the switch needs to be replaced.If the pump comes on but doesn't pump water, it's possible that the diaphragm in the pump has debris in it or it is punctured. There are three screws that attach the pump head to the pump casing. Remove these screws and inspect the rubber diaphragm. If it is damaged, replace it with the repair kit that you can get from the manufacturer. You can usually buy these at your local RV parts dealer. If the diaphragm looks okay, clean it thoroughly with a gentle detergent and flush the pump head to remove any debris that may have entered it. If it still doesn't work after doing these procedures go the next step.Check to see that supply line from the fresh water holding tank to the RV water pump isn't blocked for punctured. Sometimes there is a shut off valve on this line. Make sure that it's open. If the line is blocked with debris or ice, you'll need to clear it somehow. I have found that I can often disconnect the line at the pump and blow compressed air through the pipe. Be sure and turn the pressure down low on the compressor. You don't want to blow the line and cause a leak. If there is a leak in this supply line, it will need to be repaired or replaced. You may also want to check the connection at the inlet side of the pump to make sure it isn't sucking air.If the pump doesn't shut off. You likely have a leak somewhere in the system. It's either at the outlet connection on the pump, in the plumbing, or at the faucet. Find the leak, repair it, and you'll be back in business.
That's all I can think of off the bat that can go wrong with the system. If none of wastewater treatment these things fix your RV water pump sent me and email and I'll try to help you out.
RV Water Pump Repair Disclaimer
You and you alone are responsible if something should go wrong while repairing your RV water pump system. If you are not skilled and competent with electrical wiring or plumbing, you should have an authorized dealer do the repairs. There is always a risk of fire when working with electrical wiring. If you should make a mistake on the plumbing, it's possible for your RV to floods and cause damage.
If you mess up, don't count on me to foot the bill for the repairs. The information contained in this page is only the opinion of the author. This is what I would do if my RV was having problems with the RV water pump system.
Make any repairs at your own risk.
RV Water Pump Video
Here's a short video that will teach you how to replace an RV water pump.
So first cheap septic tanks for sale of all I m always sad all the time and I have a big group of friends but its not like I can go anywhere with them or even keep them much longer. My "mom" is the biggest part of my "depressed" state. I can t talk to anybody about it either. My mom is constantly telling at me, blocking...
So first of all I m always sad all the time and I have a big group of friends but its not like I can go anywhere with them or even keep them much longer. My "mom" is the biggest part of my "depressed" state. I can t talk to anybody about it either. My mom is constantly telling at me, blocking all of my friends out of my life, locking me up in my room, gets back with her boyfriend that has molested me and she knows it, and she says super rude remarks to me. She doesn t believe in me and I go to bed crying every night. She blames me for everything and all this has started when I was tweleve. She tells me she never wants to see me again and I can just go to hell. I sometimes have water storage tanks suicidal thoughts. I have made some pretty deep scars on my wrists and thighs... I m not old enough to just leave or drive so I have no idea what I m supposed to do. We get in soooooo many fights and have already been in 2 fights today. I m scared I concrete septic tanks price don t know what to do. She is getting back with the man that has molested me and is violent towards her. He makes us all miserable and when she brakes up with him (every week) she comes to me and yells at me. She knows how he is but she always gets back with him. Its been like this for 6 years and I really feel like I should just leave this world.... What should I do?
Summer Inman was last seen on March 22. Police have since arrested her estranged husband and her in-laws.
NEW: The mother-in-law provided details where the corpse was located, police sayNEW: The body of Summer Inman was discovered in septic tank smell in house a septic system behind a church Police have arrested the woman's estranged husband, mother-in-law and father-in-lawRead more about this story from CNN affiliate WBNS.
(CNN) -- The mother-in-law of a 25-year-old woman found dead in a septic system provided investigators with details where the corpse was located, police said Wednesday.
The mother-in-law, Sandra Inman, along with the woman's estranged husband, William Inman Jr., and the woman's father-in-law, William Inman Sr., were arrested and face kidnapping charges.
Logan, Ohio Police Chief Aaron Miller said the body of Summer Inman was discovered in a septic system behind a church in nearby Nelsonville, Ohio on Tuesday.
He said officers had to unscrew the system's cover before reaching the body.
"It would appear that she was killed very quickly," Miller told reporters. He did not provide further details.
Summer Inman's abduction and septic tank drain lines the arrests connected to her case have made national news recently.
The mother of three was working as part of a cleaning crew at a local bank on March 22, police said. When she stepped outside, she was grabbed and forced how often should you pump your septic tank into a white vehicle.
Miller said that the evidence suggests all three suspects played a role in the kidnapping, but he would not discuss whether they were involved in the apparent murder.
Summer Inman and William Inman Jr. were married in 2004 but the couple was separated, CNN affiliate WBNS reported.
Summer Inman had also filed for divorce and claimed in court documents that her husband had threatened to kill her if she took his children away, the affiliate reported.
Families that are not served by public drains usually depend upon septic systems to deal with and throw away wastewater. Septic tanks represent a significant monetary investment. If taken care of appropriately, a well designed, installed, and maintained system will certainly offer years of reliable, inexpensive service.
A failing system can become a source of pollution and public health issue, triggering building damage, ground and surface water pollution (such as well water-- both yours and your next-door neighbors), and condition break outs. As soon as your septic system fails to run successfully, you may need to change it, costing you countless dollars. Plus, if you sell your home, your septic tank must remain in excellent working order. It makes excellent sense to comprehend and care for your septic system.
There are various types of septic tanks that fit a variety of soil and site conditions. The following will certainly assist you understand the major parts of a requirement (gravity fed) septic tank and ways to keep it operating securely at the lowest possible cost.
A standard septic tank system has 3 main parts:
The Septic Tank-- A septic tank's function is to separate solids from the wastewater, store and partly decay as much solid material as possible, while permitting the liquid (or effluent) to go to the drainfield.
The Drainfield-- After solids settle septic pumping in the septic tank, the liquid wastewater (or effluent) is discharged to the drainfield, likewise referred to as an absorption or leach field.
The Soil-- The soil below the drainfield supplies the last treatment and disposal of the septic tank effluent. After the wastewater has entered the soil, organisms in the soil treat the effluent before it percolates downward and outward, eventually going into ground or surface water. The kind of soil likewise affects the effectiveness of the drainfield; for example, clay soils might be too tight to enable much wastewater to go through and gravelly soil might be too coarse to offer much treatment.
House owners and residents have a fantastic effect on septic system efficiency. Using more water than the system was developed to handle can trigger a failure. Disposal of chemical or excess organic matter, such as that from a garbage disposal, can destroy a septic system. The following maintenance ideas can help your system provide long-term, reliable treatment of family waste.
Examine and Pump Regularly
The most essential step to maintaining your septic tank is to remove sludge and scum build-up before it washes into the drainfield. How frequently your tank requires pumping depends on the size of the tank, the variety of people in your household, the volume of water made use of, and amount of solids (from humans, garbage disposals, and other wastes) going into the system. Typically, tanks must be pumped every 3 to 5 years.
Use Water Efficiently
Excessive water is a major reason for system failure. The soil under the septic system should take in all the water used in the house. Excessive water from laundry, dishwasher, toilets, baths, and showers may not permit enough time for sludge and residue to separate. The less water used, the less water entering the septic tank, leading to less risk of system failure.
Decrease Solid Garbage disposal
What decreases the drain can have a major impact on your septic tank. Lots of products do not decompose and as a result, develop in your septic tank. If you can deal with it in some other method, do so, rather than putting it into your system.
Keep Chemicals From Your System
Keep home chemicals out click me of your septic tank, such as caustic drain openers, paints, pesticides, photographic chemicals, brake fluid, gas, and motor oil. Improper disposal of harmful chemicals down the drain is dangerous to the environment, as well as the bacteria needed to break down wastes in the septic system.
Septic tank Ingredients
Adding a stimulator or a booster to a septic tank to aid it function or "to recover bacterial balance" is not essential. The naturally occurring germs required for the septic tank to work are currently present in human feces.
What Can Go Wrong?
Like a vehicle, septic systems are created to offer long-term, efficient treatment of family waste when run and maintained correctly. Nevertheless, many systems that fail prematurely are due to inappropriate maintenance.
If you see any of the following indications or if you believe your septic tank might be having issues, get in touch with a competent septic expert.
- Smells, appearing sewage, damp spots, or lush vegetation development in the drainfield area
- Plumbing or septic tank backups (commonly a black liquid with a disagreeable smell).
- Slow draining components.
- Gurgling noises in the plumbing system.
- If you have a well and tests reveal the presence of coliform (germs) or nitrates, your drainfield may be failing.
- Lush green turf over the drainfield, even during dry weather.